Separator with damping ASMNG-80-EW-08

stops one or more accumulated workpiece carriers on a defined
workpiece carrier stop surface

EXECUTION AND WEIGHT

Device design: Basic housing made of hard anodized aluminum and
stop plate made of hardened steel.
Air damping system, adjustable with throttle screw.
Weights of the devices:
ASMNG-80-EW-08: 0,27 kg
ASMNG-80-EW-08-I: 0,42 kg

EFFECTIVE PISTON AREAS, FORCES

The forces are dependent on the pneumatic pressure, the piston surface and the spring force.
During the respective working movements, the following piston surfaces are subjected to compressed air:
Piston surface for lowering (EW-type): 594 mm²
Piston surface for extending the damping piston: 380 mm²

FUNCTION

The pneumatically separator ASMNG is a separator with damping. If a workpiece carrier strikes against the stop plate of the separator, the air chamber is compressed and the compressed air escapes through the opening gap of the adjusting screw. Thus, the workpiece carrier is gently damped to a stop. The damping is with air and can be finely adjusted via a throttle screw. If the workpiece carrier will be damped, the stop plate will be pushed in. The stop plate will stay in this position. There are no forces that would try to move the stop plate even the workpiece pallet is not pushing against the stop plate. The extension of the stop plate is effected by an internal valve control in the separator, when lowering, when the separator has reached the lower position.

SPRING FORCES

In its basic version “EW” = “single acting”, the separator ASMNG has a compression spring which moves the separator into its upper or raised position.
The spring forces are:
Raised position: F1 = 55 N
Lowered position: F2 = 110 N

TEMPERATURE RANGE

Temperature range: +5°C up to + 60°C (without accessories)

AIR CONNECTION

The separators ASMNG are offered as single-acting variants. There is only one air connection (P1) for lowering the separator. This air connection is located on the back or front of the unit. Usually, the front air connection is closed by a blanking plug.

OPERATING PRESSURE AND AIR CONSUMPTION

Operating pressure 4 –8 bar
Single acting function:
Cylinder volume V for lowering + extending the stop plate:
ASMNG-80-EW-08: 4.8 cm³ + 9.1 cm³ = 13.9 cm³
The air consumption in liter (Nl) can be calculated by using a formula:
Q = V⋅(p+0,1)⋅0,01
Here is:
Q … air consumption in liter (Nl)
V … Cylinder volume (cm³)
p … Supply pressure in MPa (6 bar = 0,6 MPa)
For 0,6 MPa pneumatic pressure the air consumption for the ASMNG-80-EW-08 is Q = 0.0973 Nl each cycle.

Datasheet / Operating manual – PDF
Step-file –> Downloadable below at the variants

Overview of the accessories for ASMNG – PDF

75000001
Fastening set with long guide sleeves

75000036
Fastening set with long guide sleeves

75000002
Fastening set B with short guide sleeves

14010004
Push-in L-fitting, M5, for tubing O.D. 6 mm

14010009
Push-in fitting, M5, for tubing O.D. 6 mm

14010006
Supply air one way flow valve, M5, for tubing O.D. 6 mm

75003073
Switch bracket

1500004
Inductive sensor M12x1, L = 45 mm, Sn = 4 mm

15010001
Plug connector, angled, M12x1, cable length 5 m

15030001
Mounting clamp M16x1, short Version

Operating rangev = (m/min)691215182430
ASMNG-80-EW-100Mass WT (kg)1 - 801 - 601 - 501 - 451 - 371 - 281 - 20

The values, given in the table above for the permissible total weight of the accumulated workpiece carriers (WT) and the permissible conveying speed, apply with a belt friction of µ=0,07 between workpiece carrier and conveyor band and with the use of an ASUTEC standard stop. To select the suitable separator, we recommend the use of our online product finder.
The specified weight range is composed of the minimum workpiece carrier weight mmin and the maximum workpiece carrier weight mmax.
Minimum propulsive force: The minimum propulsive force can be calculated using the formula FRmin = mmin · g · µ.
For the ASMNG-80-EW-08 -> FRmin = 0,69 N. This minimum propulsive force must not be less than this, in order to ensure that the stop can be pushed by the WT into its damped (retracted) position.
Maximum propulsive force:
FRmax = 55 N. This maximum propulsive force may not be exceeded in order to ensure a sufficient damping effect.
FRmax = 110 N. This maximum propulsive force may not be exceeded in order to ensure a sufficient force for lowering.
Adjustment of damping: The adjustment of the damping effect can be regulated within a certain range. As an experience value can be stated that when the damping is adjusted to a certain weight, other weights in a range of ± 50% can be damped properly with this setting.
For example: Damping optimally adjusted to 30 kg mass to be dampened -> Damping of masses from 15 kg to 45 kg well possible. At lower masses, the damping end position is reached late or not at all. At higher masses, the damping is not strong enough and the speed of the workpiece carrier at the damping end position is still too high and the workpiece carrier will be abruptly stopped.

ASMNG-80-EW-08

*Preferred variant*
Separator with 24 mm damping stroke for workpiece carrier loads from 1 kg up to 80 kg
Single acting function, 8 mm lowering stroke
Step-file

Title

Your Name

Your Company

Your E-mail address

Your Phone number

ASMNG-80-EW-08-100

*Preferred variant*
Separator with 24 mm damping stroke for workpiece carrier loads from 1 kg up to 80 kg
Single acting function, 8 mm lowering stroke
Delivery including air connector 14010004 and fastening set 75000001
Step-file

Title

Your Name

Your Company

Your E-mail address

Your Phone number

ASMNG-80-EW-08-I

*Preferred variant*
Separator with 24 mm damping stroke for workpiece carrier loads from 1 kg up to 80 kg
Single acting function, 8 mm lowering stroke
“I” Sensing option: Possibility to query the upper and lower position with the aid of inductive sensors
Step-file

Title

Your Name

Your Company

Your E-mail address

Your Phone number

ASMNG-80-EW-08-I-100

*Preferred variant*
Separator with 24 mm damping stroke for workpiece carrier loads from 1 kg up to 80 kg
Single acting function, 8 mm lowering stroke
“I” Sensing option: Possibility to query the upper and lower position with the aid of inductive sensors
Delivery including air connector 14010004 and fastening set 75000001
Step-file

Title

Your Name

Your Company

Your E-mail address

Your Phone number

ADDITIONAL VARIANTS ON REQUEST: +49 (0)7024-80594-0

Comments are closed.

×